Topology
Addressing Table
Device
|
Interface
|
IP Address
|
Subnet Mask
|
Default Gateway
|
R1
|
G0/0
|
192.168.0.1
|
255.255.255.0
|
N/A
|
|
G0/1
|
192.168.1.1
|
255.255.255.0
|
N/A
|
S1
|
VLAN 1
|
N/A
|
N/A
|
N/A
|
PC-A
|
NIC
|
192.168.1.3
|
255.255.255.0
|
192.168.1.1
|
PC-B
|
NIC
|
192.168.0.3
|
255.255.255.0
|
192.168.0.1
|
Objectives
Part 1: Set Up the Topology and Initialize
Devices
Part 2: Configure Devices and Verify Connectivity
Part 3: Configure Router to Allow CCP
Access
Part 4: (Optional) Install and Set Up
CCP on PC-A
Part 5: Configure R1 Settings Using
CCP
Part 6: Use CCP Utilities
Background / Scenario
Cisco Configuration
Professional (CCP) is a PC-based application that provides GUI-based device
management for Integrated Services Routers (ISRs). It simplifies the configuration
of routing, firewall, VPN, WAN, LAN, and other settings through menus and easy-to-use
wizards.
In this lab, you will configure the
router settings using the configuration from the previous lab in this chapter. Layer
3 connectivity must be established between the PC running CCP (PC-A) and R1 before
CCP can establish a connection. In addition, HTTP access and authentication
must be configured on R1.
You will download and install CCP on the PC
and then use it to monitor R1’s interface status, configure an interface, set
the date and time, add a user to the local database, and edit vty settings. You
will also use some of the utilities included in CCP.
Note: Router configurations performed using CCP generate IOS CLI
commands. CCP can be very useful for configuring more complex router features because
it does not require specific knowledge of the Cisco IOS command syntax.
Note: The routers used with CCNA hands-on labs
are Cisco 1941 Integrated Services Routers (ISRs) with Cisco IOS Release 15.2(4)M3
(universalk9 image). The switches used are Cisco Catalyst 2960s with Cisco IOS Release
15.0(2) (lanbasek9 image). Other routers, switches, and Cisco IOS versions can
be used. Depending on the model and Cisco IOS version, the commands available
and output produced might vary from what is shown in the labs. Refer to the
Router Interface Summary Table at the end of this lab for the correct interface
identifiers.
Note: Make sure that the router and switch have been erased and have no
startup configurations. If you are unsure, contact your instructor.
Required Resources
·
1 Router (Cisco 1941 with Cisco
IOS Release 15.2(4)M3 universal image or comparable)
·
1 Switch (Cisco 2960 with Cisco
IOS Release 15.0(2) lanbasek9 image or comparable)
·
2 PCs (Windows 7, Vista, or XP
with terminal emulation program, such as Tera Term)
·
Console cables to configure the
Cisco IOS devices via the console ports
·
Ethernet cables as shown in the
topology
Note: PC system requirements for CCP version 2.6 are:
·
2 GHz processor or faster
·
1 GB DRAM minimum; 2 GB
recommended
·
400 MB of available hard disk
space
·
Internet Explorer 6.0 or above
·
Screen resolution of 1024x768 or
higher
·
Java Runtime Environment (JRE)
version 1.6.0_11 or later.
·
Adobe Flash Player version 10.0
or later, with Debug set to No
Note: The Gigabit Ethernet interfaces on Cisco 1941 ISRs are autosensing
and an Ethernet straight-through cable may be used between the router and PC-B.
If using another model Cisco router, it may be necessary to use an Ethernet
crossover cable.
Part 1: Set Up the Topology and Initialize Devices
Step 1:
Cable the network as shown in
the topology.
a.
Attach the devices shown in the
topology diagram, and cable as necessary.
b.
Power on all the devices in the
topology.
Step 2:
Initialize and reload the router
and switch.
Part 2: Configure Devices and Verify Connectivity
In Part 2, you will configure basic settings,
such as the interface IP addresses (G0/1 only), secure device access, and
passwords. Refer to the Topology and Addressing Table for device names and address
information.
Step 1:
Configure the PC interfaces.
a.
Configure the IP address,
subnet mask, and default gateway settings on PC-A.
b.
Configure the IP address,
subnet mask, and default gateway settings on PC-B.
Step 2:
Configure the router.
Note: Do NOT configure interface G0/0 at this time. You will configure
this interface using CCP later in the lab.
a.
Console into the router and
enable privileged EXEC mode.
b.
Enter into global configuration
mode.
c.
Disable DNS lookup.
d.
Assign a device name to the
router.
e.
Require that a minimum of 10
characters be used for all passwords.
f.
Assign cisco12345 as the privileged EXEC encrypted password.
g.
Assign ciscoconpass as the console password and enable login.
h.
Assign ciscovtypass as the vty password and enable login,
i.
Configure logging synchronous on the console and vty lines.
j.
Encrypt the clear text
passwords.
k.
Create a banner that warns anyone
accessing the device that unauthorized access is prohibited.
l.
Configure the IP addresses, an
interface description, and activate G0/1 interface on the router.
m.
Save the running configuration
to the startup configuration file.
Step 3:
Verify network connectivity.
Verify that you can ping R1 G0/1 from
PC-A.
Part 3:
Configure the Router to
Allow CCP Access
In Part 3, you will set up the router to
allow CCP access by enabling HTTP and HTTPS server services. You will also
enable HTTP authentication to use the local database.
Step 1:
Enable HTTP and HTTPS server
services on the router.
R1(config)# ip
http server
R1(config)# ip
http secure-server
Step 2:
Enable HTTP authentication to
use the local database on the router.
R1(config)# ip
http authentication local
Step 3:
Configure the router for CCP
access.
Assign a user in the router local
database for accessing CCP using username admin
and password adminpass1.
R1(config)# username
admin privilege 15 secret adminpass1
Part 4: (Optional) Install and Set Up CCP on PC-A
Step 1:
Install CCP.
Note: This step can be skipped if CCP is already installed on PC-A.
a.
Download CCP 2.6 from Cisco’s
website:
b.
Choose the cisco-config-pro-k9-pkg-2_6-en.zip file.
Note: Verify that you select the correct CCP file and not CCP Express.
If there is a more current release of CCP, you may choose to download it; however,
this lab is based on CCP 2.6.
c.
Agree to the terms and
conditions, and download and save the file to the desired location.
d.
Open the zip file and run the
CCP executable.
e.
Follow the on-screen
instructions to install CCP 2.6 on your PC.
Step 2:
Change settings to run as the
administrator.
CCP may fail to launch correctly if it is
not run as an administrator. You can change the launch settings so that it
automatically runs in administrator mode.
a.
Right-click the CCP desktop icon (or click the Start button) and then right-click Cisco Configuration Professional. In
the drop-down list, select Properties.
b.
In the Properties dialog box,
select the Compatibility tab. In the
Privilege Level section, click the Run
this program as an administrator checkbox, and then click OK.
Step 3:
Create or manage communities.
a.
On PC-A, start CCP. (Double-click
the CCP desktop icon or click Start > Cisco Configuration Professional.)
b.
If you receive a security
warning message prompting to allow the CiscoCP.exe program to make changes to
the computer, click Yes.
c.
When CCP starts, the Select / Mange Community dialog box
displays. Enter the IP address for R1 G0/1, and the username admin and password adminpass1 that you added to the local database during the router
configuration in Part 2. Click OK.
d.
In the Community Information
window, click Discover.
If you have configured the router
correctly, the Discovery Status changes from Not discovered to Discovered,
and R1 appears in the Router Hostname column.
Note: If there is a problem with your configuration, you will see a “Discovery
failed” status. Click Discovery Details
to determine why the discovery process failed and then troubleshoot the
problem.
Part 5: Configure R1 Settings Using CCP
In Part 5, you will use CCP to display
information about R1, configure interface G0/0, set the date and time, add a
user to the local database, and change your vty settings.
Step 1:
View the status of the
interfaces on R1.
a.
On the CCP toolbar, click Monitor.
b.
In the left navigation pane, click
Router > Overview to display the Monitor Overview screen in the right content
pane.
c.
Use the up and down arrows to
the right of the interface list to scroll through the list of interfaces for
the router.
Step 2:
Use the Ethernet LAN wizard to
configure interface G0/0.
a.
On the CCP toolbar, click Configure.
b.
In the left navigation pane,
click Interface Management > Interface and Connections to display
the Interfaces and Connections screen in the right content pane.
c.
Click Create New Connection to start the Ethernet LAN wizard.
d.
When you are prompted to enable
AAA on the router, click No.
e.
Click Next to be guided through the Layer 3 Ethernet interface creation
process.
f.
Keep the Configure this interface for straight routing radio button selected
and click Next.
g.
Enter 192.168.0.1 in the IP address field and 255.255.255.0 in the Subnet mask field and click Next.
h.
Keep the No radio button selected on the DHCP server screen and click Next.
i.
Review the summary screen and
click Finish.
j.
Click the Save running config to device’s startup config check box, and then
click Deliver. This adds the
commands shown in the preview window to the running configuration, and then
saves the running configuration to the startup configuration on the router.
k.
The Commands Delivery Status
window displays. Click OK to close
this window. You will be routed back to the Interfaces and Connections screen;
G0/0 should have turned green and displayed as Up in the Status column.
Step 3:
Set the date and time on the
router.
a.
In the left navigation pane,
select Router > Time > Date and Time to display the Additional Tasks > Date/Time screen
in the right content pane. Click Change
Settings….
b.
In the Date and Time Properties
window, edit the Date, Time, and Time Zone. Click Apply.
c.
In the Router’s clock
configured window, click OK. In the
Date and Time Properties window, click Close.
Step 4:
Add a new user account to the
local database.
a.
In the left navigation pane,
select Router > Router Access > User Accounts/View to display the Additional Tasks > User
Accounts/View screen in the content pane on the right. Click the Add… button.
b.
Enter ccpadmin in the Username: field. Enter ciscoccppass in the New Password: and Confirm New Password: fields.
Select 15 in the Privilege Level:
drop-down list. Click OK to add this
user to the local database.
c.
In the Deliver Configuration to
Device window, click the Save running
config to device’s startup config check box, and then click Deliver.
d.
Review the information in the
Commands Delivery Status window, and click OK.
The new user account should now appear in the content pane on the right.
Step 5:
Edit vty line settings.
a.
In the left navigation pane,
select Router Access > VTY to display the Additional Tasks
> VTYs screen in the content pane on the right. Click Edit….
b.
In the Edit VTY Lines window,
change the Time out: field to 15
minutes. Click the Input Protocol
> Telnet check box. Review the
other options available. Also select the SSH
checkbox. Then click OK.
c.
Review the commands that will
be delivered to the running configuration on the Deliver Configuration to
Device screen and click Deliver. In
the Commands Delivery Status window, click OK.
The content pane on the right should reflect the changes to the EXEC timeout
value.
Part 6: Use CCP Utilities
In Part 6, you will use the Utilities
pane to save the router’s running configuration to the startup configuration. The
Ping utility will be used to test network connectivity, and the View utility will
be used to show the router’s running configuration. Finally, you will close CCP.
Step 1:
Save the router’s running configuration
to the startup configuration.
a.
At the bottom of the left
navigation pane, locate the Utilities pane. Click Write to Startup Configuration.
b.
The content pane displays a
confirmation screen. Click Confirm. An
Information window displays, letting you know that the configuration was saved
successfully. Click OK.
Step 2:
Use the Ping utility to test
connectivity to PC-B.
a.
In the Utilities pane, click Ping and Traceroute to display the Ping
and Traceroute screen in the content pane. Enter 192.168.0.3 in the Destination*: field and then click Ping. Use the scrollbar to the right of
the results box to view the results of your ping.
Step 3:
Use the View utility to show
the running configuration for the router.
a.
In the Utilities pane, click View > IOS Show Commands to display the IOS Show Commands screen in the
content pane.
b.
Select show run from the drop-down list and click Show. The router’s running configuration is displayed in the
content pane.
Step 4:
Close CCP.
Close the CCP window. When a Windows
Internet Explorer confirmation window displays, click Leave this page.
Reflection
1.
What transport protocol does CCP
use to access the router and what commands are used to allow access?
_______________________________________________________________________________________
_______________________________________________________________________________________
2.
What router command tells CCP
to use the local database to authenticate?
_______________________________________________________________________________________
3.
What other show commands are available in the Utilities pane of CCP?
_______________________________________________________________________________________
_______________________________________________________________________________________
4.
Why would you want to use CCP
instead of the IOS CLI?
_______________________________________________________________________________________
_______________________________________________________________________________________
_______________________________________________________________________________________
Router Interface Summary Table
Router Interface Summary
|
||||
Router Model
|
Ethernet Interface #1
|
Ethernet Interface #2
|
Serial Interface #1
|
Serial Interface #2
|
1800
|
Fast Ethernet 0/0 (F0/0)
|
Fast Ethernet 0/1 (F0/1)
|
Serial 0/0/0 (S0/0/0)
|
Serial 0/0/1 (S0/0/1)
|
1900
|
Gigabit Ethernet 0/0 (G0/0)
|
Gigabit Ethernet 0/1 (G0/1)
|
Serial 0/0/0 (S0/0/0)
|
Serial 0/0/1 (S0/0/1)
|
2801
|
Fast Ethernet 0/0 (F0/0)
|
Fast Ethernet 0/1 (F0/1)
|
Serial 0/1/0 (S0/1/0)
|
Serial 0/1/1 (S0/1/1)
|
2811
|
Fast Ethernet 0/0 (F0/0)
|
Fast Ethernet 0/1 (F0/1)
|
Serial 0/0/0 (S0/0/0)
|
Serial 0/0/1 (S0/0/1)
|
2900
|
Gigabit Ethernet 0/0 (G0/0)
|
Gigabit Ethernet 0/1 (G0/1)
|
Serial 0/0/0 (S0/0/0)
|
Serial 0/0/1 (S0/0/1)
|
Note: To find out how the router is configured, look at the interfaces
to identify the type of router and how many interfaces the router has. There
is no way to effectively list all the combinations of configurations for each
router class. This table includes identifiers for the possible combinations
of Ethernet and Serial interfaces in the device. The table does not include
any other type of interface, even though a specific router may contain one.
An example of this might be an ISDN BRI interface. The string in parenthesis
is the legal abbreviation that can be used in Cisco IOS commands to represent
the interface.
|
No comments:
Post a Comment